feat(boot): Add SUB-OS boot logo and splash, share the console font, and lift the kernel size ceiling

Boot logo (init/bootlogo.c, init/logo_data.c, scripts/mklogo.py):
  The logo appears in two forms because the framebuffer does not exist for the
  first third of boot. An ASCII rendition goes to the text console and serial
  line from the first moments; once the video driver is up at step [5/14] the
  real bitmap takes over as a graphical splash with a progress bar tied to the
  actual boot stages.

  The asset is 4-bit palette indexed, so 160x160 pixels cost 12.5 KB instead of
  100 KB, and carries a transparency mask so the mark composites onto the
  gradient rather than stamping a flat rectangle over it. scripts/mklogo.py
  regenerates init/logo_data.c from the source PNG.

  Boot reaches the desktop in well under a second, so the splash is held for a
  minimum duration and the bar sweeps to 100% during the hold; without that the
  logo would flash past unseen. `splashtime=<ms>` tunes it and `nosplash`,
  `nogui` or `text` skip it.

Bootloader (boot/stage2.asm):
  stage2 staged the whole kernel in conventional RAM before copying it to 1 MB,
  which capped the kernel at roughly 576 KB before the load ran into video
  memory at 0xA0000. The logo pushed it over that line and the kernel stopped
  booting. Each 32 KB chunk now goes into one fixed low buffer and is copied
  straight to its final address, using unreal mode for the 32-bit reach. The
  ceiling is now the image itself, 1.375 MB.

Console font (lib/font8x8.c):
  fb_draw_char was a stub that ignored its character argument and drew a filled
  rectangle, which is why the splash rendered its text as solid blocks. It now
  renders real glyphs, and the table it uses is shared: the framebuffer console,
  the canvas rasterizer and the desktop compositor had three divergent private
  copies, two of which still carried the `// \` line-continuation defect.

printk console sink (kernel/printk.c):
  printk output can be redirected to a callback, so a caller can run a subsystem
  that reports via printk and capture what it printed. Serial and the dmesg ring
  still see everything, which keeps a captured run debuggable.

Shell builtins (userland/lazybox/shell.c):
  The builtin chain is extracted into shell_execute_builtin(), so the kernel TTY
  and the desktop terminal accept the same vocabulary instead of the GUI seeing
  only the applet table. Callers that cannot be suspended pass allow_blocking =
  false to refuse the animating ones.

Co-Authored-By: Claude Opus 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01L5yKJT4Wo2cV3rfPrwY5MP

include/kernel/printk.h

@@ -4,6 +4,7 @@
 #include <stddef.h>
 #include <stdint.h>
 #include <stdarg.h>
+#include <stdbool.h>
 #include <lib/printf.h>
 
 // Linux-compatible log level prefixes
@@ -50,4 +51,20 @@ int  kprintf(const char* fmt, ...); // Alias for compatibility
 void dmesg_dump(void);
 const char* dmesg_get_buffer(size_t* size_out);
 
+// ---------------------------------------------------------------------------
+// Console redirection
+//
+// While a sink is installed, printk output is handed to the callback instead
+// of the text console, so a caller can run a subsystem that reports via printk
+// and capture what it printed. The serial console and the dmesg ring still
+// receive everything, which keeps a captured run debuggable.
+//
+// The sink must not itself call printk; re-entrant output is dropped.
+// ---------------------------------------------------------------------------
+typedef void (*printk_sink_fn_t)(const char* text, size_t len, void* ctx);
+
+void printk_set_sink(printk_sink_fn_t fn, void* ctx);
+void printk_clear_sink(void);
+bool printk_has_sink(void);
+
 #endif // _KERNEL_PRINTK_H