Add three real platform device drivers (x86 hardware, ARM-stubbed):
- drivers/timer/hpet.c + include/drivers/hpet.h: High Precision Event Timer.
Maps the HPET block at the standard 0xFED00000, reads the femtosecond period
from the capability register, enables the main counter and exposes a
monotonic nanosecond time source (hpet_get_ns) far finer than the 100 Hz PIT.
- drivers/char/lpt.c + include/drivers/lpt.h: IBM PC parallel port (LPT1) with
the Centronics data/strobe handshake over ports 0x378/0x379/0x37A.
- drivers/char/nvram.c + include/drivers/nvram.h: MC146818 CMOS NVRAM read/write
over 0x70/0x71, preserving the NMI-disable bit, with checksum and hex dump.
Wired all three into the [5/14] device-enumeration boot step and added LazyBox
applets `hpet`, `lpt`, and `nvram`.
Verified live under QEMU (screenshotted): HPET reports 100 MHz / 3 comparators /
10 ns period and its counter advances ~1.4 s of real time between two `hpet`
runs; NVRAM dumps 128 bytes with a computed checksum; LPT1 detected at 0x378.
Clean build on x86_64/aarch64/armv8i; 0 panics / 0 OOM.
Co-Authored-By: Claude Opus 4.8 <[email protected]>
Claude-Session: https://claude.ai/code/session_01Fh5z6V7nGPbHvqVG5p4CXX
Pressing Esc left the desktop and started the shell, but nothing appeared in the
emulator window -- the session was only visible on the host terminal. Once the
VBE adapter is switched into graphics mode the VGA text buffer at 0xB8000 stops
being scanned out, so every printk after that point reached serial and the
dmesg ring but never the display.
Disabling the DISPI interface does not bring the text console back; QEMU keeps
presenting the last framebuffer surface. So rather than clawing the adapter back
to text mode, the console is now rendered into the framebuffer:
drivers/video/fbcon.c draws the console with the shared 8x8 font and carries a
VT100 subset -- SGR colours, cursor addressing, relative moves, erase-display,
erase-line and save/restore. It presents a fixed 80x25 grid, because that is
the geometry the userland assumes (nano pads its bars with %-80s, the shell
wraps at TTY_WIDTH), with the glyph cell scaled to fill the active resolution.
The TTY driver became the console dispatcher: tty_write, tty_clear and
tty_set_cursor route to fbcon while it owns the display. That last one is what
makes nano work -- it positions with tty_set_cursor() rather than escapes, so
its full-screen repaint was landing as an append-only stream.
Also in this change:
- `video=WIDTHxHEIGHT` on the kernel command line selects the display mode,
defaulting to 1280x720 so a 16:9 host panel is filled rather than pillarboxed
when QEMU goes fullscreen. Rejects modes the heap cannot back.
- `make run-fullscreen`, plus zoom-to-fit on the windowed target, so scaling
preserves the guest aspect ratio instead of stretching it.
- QEMU targets raise vgamem_mb, since a 1280x720 32-bit surface exceeds the
default VGA memory.
- bochs_vbe_disable()/fb_set_active() let the framebuffer be marked dormant so
drawing routines no-op after a mode teardown.
Co-Authored-By: Claude Opus 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01L5yKJT4Wo2cV3rfPrwY5MP
Boot logo (init/bootlogo.c, init/logo_data.c, scripts/mklogo.py):
The logo appears in two forms because the framebuffer does not exist for the
first third of boot. An ASCII rendition goes to the text console and serial
line from the first moments; once the video driver is up at step [5/14] the
real bitmap takes over as a graphical splash with a progress bar tied to the
actual boot stages.
The asset is 4-bit palette indexed, so 160x160 pixels cost 12.5 KB instead of
100 KB, and carries a transparency mask so the mark composites onto the
gradient rather than stamping a flat rectangle over it. scripts/mklogo.py
regenerates init/logo_data.c from the source PNG.
Boot reaches the desktop in well under a second, so the splash is held for a
minimum duration and the bar sweeps to 100% during the hold; without that the
logo would flash past unseen. `splashtime=<ms>` tunes it and `nosplash`,
`nogui` or `text` skip it.
Bootloader (boot/stage2.asm):
stage2 staged the whole kernel in conventional RAM before copying it to 1 MB,
which capped the kernel at roughly 576 KB before the load ran into video
memory at 0xA0000. The logo pushed it over that line and the kernel stopped
booting. Each 32 KB chunk now goes into one fixed low buffer and is copied
straight to its final address, using unreal mode for the 32-bit reach. The
ceiling is now the image itself, 1.375 MB.
Console font (lib/font8x8.c):
fb_draw_char was a stub that ignored its character argument and drew a filled
rectangle, which is why the splash rendered its text as solid blocks. It now
renders real glyphs, and the table it uses is shared: the framebuffer console,
the canvas rasterizer and the desktop compositor had three divergent private
copies, two of which still carried the `// \` line-continuation defect.
printk console sink (kernel/printk.c):
printk output can be redirected to a callback, so a caller can run a subsystem
that reports via printk and capture what it printed. Serial and the dmesg ring
still see everything, which keeps a captured run debuggable.
Shell builtins (userland/lazybox/shell.c):
The builtin chain is extracted into shell_execute_builtin(), so the kernel TTY
and the desktop terminal accept the same vocabulary instead of the GUI seeing
only the applet table. Callers that cannot be suspended pass allow_blocking =
false to refuse the animating ones.
Co-Authored-By: Claude Opus 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01L5yKJT4Wo2cV3rfPrwY5MP
Three build-correctness fixes plus README coverage of the new kernel core.
The Makefile had no header dependency tracking, so editing a header left every
unrebuilt caller linked against the old layout. That is how the desktop's
window paint callbacks silently landed at the wrong struct offset after
gui_window_t grew: gui_apps.o was never recompiled. Compiles now emit .d files
via -MMD -MP and the build pulls them in.
The include has to sit at the end of the file with .DEFAULT_GOAL pinned to
`all` -- a .d file's first rule would otherwise become make's default goal and
turn a bare `make` into a silent no-op.
drivers/video/canvas.c carried the same font table defect gui_gfx.c did: the
`// \` comment on the backslash glyph continues onto the next line, swallowing
the `]` entry and shifting every glyph from ']' onward by one, so all lowercase
text rendered one letter off.
Co-Authored-By: Claude Opus 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01L5yKJT4Wo2cV3rfPrwY5MP
- Upgrade resolution to 800x600 @ 32bpp TrueColor with Bochs/QEMU VBE LFB
- Implement full 8042 Aux PS/2 mouse controller driver on IRQ 12 (vector 44) with packet decode and bounds clamping
- Add high-definition 8x16 font rasterizer with text drop shadows for sharp typography
- Upgrade to smooth 16x24 anti-aliased cursor with dark slate outline and drop shadow
- Increase titlebars to 24px and taskbar to 32px with modern desktop styling
- Re-architect applications (SysMon, Terminal, Explorer, Calc, Paint, About) for spacious high-res display
- Integrate Bochs/QEMU VBE physical LFB mapping directly to hardware video memory (0xFD000000)
- Update kernel boot sequence to directly boot into GUI Desktop by default
- Fall back to Emergency Kernel TTY Mode upon GUI exit (Esc key / Exit menu item)
- Support 'nogui', 'text', 'emergency', and 'single' boot arguments to boot directly into text mode
- Remove frame limits so GUI runs persistently
- Implement Intel 82574L / 82567LM / I217 / I219 PCIe Gigabit NIC driver with DMA ring buffers and auto-negotiation in drivers/net/e1000e.c and include/drivers/e1000e.h
- Implement VirtIO-GPU 2D hardware graphics display adapter driver with dirty rect flushing in drivers/virtio/virtio_gpu.c and include/drivers/virtio_gpu.h
- Implement Dynamic CPU Frequency Scaling and ACPI CPPC Power Governor with performance, powersave, ondemand, conservative, and schedutil policies in drivers/power/cpufreq.c and include/drivers/cpufreq.h
- Implement VirtIO-Input para-virtualized tablet/mouse event driver in drivers/virtio/virtio_input.c and include/drivers/virtio_input.h
- Expand stage2 kernel bootloader loading boundary to 768 KB (1536 sectors)
- Add LazyBox applets: 'cpufreq', 'gpuinfo', 'e1000e'
- Verified across x86_64, AArch64, and ARMv8i targets
- Add 'clear' and 'cls' builtin handlers in LazyBox shell
- Output ANSI \033[2J\033[H sequence on tty_clear() to clear serial/UART terminals
- Support both ASCII 0x7F (DEL) and 0x08 (BS) for Backspace in shell and nano editor
- Connect 16550 serial input to keyboard_get_key() on x86_64 for headless terminals
- Add ANSI escape sequence decoding for arrow keys (Up/Down/Left/Right/Home/End/Del)
- Update Makefile 'make run' and 'make qemu' with -display none for smooth terminal execution
- Add 'make run-gui' target for optional graphical SDL/GTK window
